Anchor Bolt Design
This lesson covers the basis for these changes two major changes to the anchor bolt design provisions in the 2016 edition of TMS 402. One change was to increase the calculated shear crushing strength by 67%. The other change was to go from a linear interaction equation for combined bending and shear to an elliptical interaction equation.
$75.00
Description
There were two major changes to the anchor bolt design provisions in the 2016 edition of TMS 402. One change was to increase the calculated shear crushing strength by 67%. The other change was to go from a linear interaction equation for combined bending and shear to an elliptical interaction equation. This lesson covers the basis for these changes. In addition to the changes in TMS 402, ASCE 7-16 reduced the required load increase for seismic applications when the anchor bolt failure is not yielding from 2.5 to 2.0. The lesson also covers general anchor bolt design in masonry, provides practical design tips, and shows examples of anchor bolt design.
Learning Objectives:
- Understand the changes, and the basis for the changes, to anchor bolt design provisions in TMS 402.
- Understand the design of anchors bolts in tension.
- Understand the design of anchor bolts in shear.
- Understand the design of anchor bolts in combined tension and shear.
Related products
-
Design
Strength Design of Masonry #5 – Strength Design of Columns and Pilasters & System Behavior
$75.00 Add to cartStrength Design of Masonry #5 – Strength Design of Columns and Pilasters & System Behavior
Masonry columns and pilasters are often used in masonry buildings to carry large, concentrated loads, and, for pilasters, to support walls subjected to out-of-plane loads. Required detailing of these elements will be reviewed and strength design provisions will be introduced for these elements. This session of also looks at several sample masonry buildings to discuss system behavior and overall design methodology for masonry structures.
Get all 6 Strength Design of Masonry lessons at a discounted rate when buying the Strength Design of Masonry bundle. Save $30 compared to buying them separately.
SKU: LMS2105 Categories: Design, Member Discount-75, Strength Design, Strength Design Series$75.00 -
Design
Strength Design of Masonry #1 – Introduction to Strength Design of Masonry and Design Methodologies
$75.00 Add to cartStrength Design of Masonry #1 – Introduction to Strength Design of Masonry and Design Methodologies
This introductory session will review basic strength design concepts for masonry, noting key differences with procedures for concrete.
Get all 6 Strength Design of Masonry lessons at a discounted rate when buying the Strength Design of Masonry bundle. Save $30 compared to buying them separately.
SKU: LMS2101 Categories: Design, Member Discount-75, Strength Design, Strength Design Series$75.00 -
TMS 402/602-16 Code and Specification Update
The TMS 402/602-16 (formerly designated as TMS 402/ACI 530/ASCE 5 and TMS 602/ASCE 530.1/ASCE 6) has been released and adopted by the 2018 edition of the International Building Code and International Residential Code for the design and construction of structural masonry, masonry veneer, and glass unit masonry.
This lesson provides updates for the major updates and changes to the 2016 TMS 402/602, with a short review on changes that will be made in the 2018 International Building Code’s masonry provisions. The 1.5 hour video is presented by Dr. Richard M. Bennett, Chair of the Committee that developed these provisions.
This lesson is intended for designers, contractors, and others to help them understand the main updates made to these codes and standards from the earlier TMS 402/602-13 and the 2015 IBC. It is assumed that the user has familiarity with those earlier documents.
This course is free to TMS Members. See more membership benefits and become a member here. If you’re already a Member, log in to access this course from your Course Dashboard.
SKU: LMS1701 Categories: Codes & Standards, Free for Members$75.00$50.00 -
Anchoring
Special Inspection of Structural Masonry #3 – Reinforcement and Connectors
$75.00 Add to cartSpecial Inspection of Structural Masonry #3 – Reinforcement and Connectors
This lesson will review common types of reinforcement, ties and anchors used in masonry along with requirements on their manufacture and use while discussing which ones are preferred and why.
Get all 9 Special Inspection of Structural Masonry lessons at a discounted rate when buying the Special Inspection of Structural Masonry bundle. Members save an additional $175 off Member price and Non-Members save $75 compared to buying them separately.
SKU: LMS1905 Categories: Anchoring, Member Discount-75, Reinforcement, Special Inspection of Masonry Series$75.00